Is That Non-Stick Coating Compliant? GB 4806.10-2025 Sets the Limits

GB 4806.10-2025GB 4806.10-2025food contact materialsnon-stick coatingmigration limitsfood safety standard

Buyers of non-stick pans care whether the coating flakes. Manufacturers care about a different question: do substances in the coating migrate into food, and how much is too much. GB 4806.10-2025 is the national standard that answers it.

Key facts first

ItemDetail
DesignationGB 4806.10-2025
TitleNational food safety standard — Coatings and layers for food contact materials and articles
Published2025-09-02
Effective2026-09-02 (in force)
ReplacesGB 4806.10-2016
Issued byNational Health Commission; State Administration for Market Regulation

This is more than a new number. It also consolidates base materials for coatings from 23 official announcements (from No. 14 of 2014 through No. 3 of 2023), so checking a base material no longer means digging through a stack of announcements — the standard plus Annex A covers it.

What it covers

The definition is precise:

Coatings intended to be applied to food contact materials and articles, in direct contact with food, or in indirect contact where their constituents may transfer into food, and the coating (film) they form.

Three elements:

  • Intended to be applied to food contact materials — not all coatings, only those on food contact surfaces
  • Direct contact, or indirect contact where constituents may migrate — indirect counts too (can exterior coatings, interlayer coatings in packaging)
  • The coating and the film it forms — the coating itself and the cured film

So: non-stick pan coatings, rice cooker inner-pot coatings, can interior coatings, coatings on food machinery contact surfaces, and coatings on paper food packaging are all in scope.

Raw materials: two separate tracks

Clause 4.1 splits the requirements:

  • Base materials — per Annex A and the relevant announcements (the 23 consolidated in this edition)
  • Additives — per GB 9685 (additives for food contact materials) and the relevant announcements

Don't mix them up: base materials go to Annex A, additives go to GB 9685.

Sensory requirements (Table 1)

For coatings in direct contact with food:

ItemRequirement
SensorySurface flat, uniform colour, no pores; after immersion, no cracking, blistering or detachment
Immersion liquidNo colouring, turbidity, sediment, off-odour or other sensory deterioration

Note "after immersion" — the assessment is on the soaked article, not the new one. Poorly adhered coatings fail here.

The four limits (Table 2)

This is the hard part — actual values:

ItemLimitTest method
Overall migration≤ 10 mg/dm²GB 31604.8
Potassium permanganate consumption≤ 10 mg/kgGB 31604.2
Heavy metals (as Pb)≤ 1 mg/kgGB 31604.9
Total primary aromatic amines migrationNot detectable (LOD 0.01 mg/kg)GB 31604.52

Three footnotes that are easy to miss:

  1. For coatings on food contact materials for infants and young children, convert results to mg/kg using the actual area-to-volume ratio — limit ≤ 60 mg/kg
  2. Cookware coatings are tested by "boiling 0.5 h, then 24 h at room temperature"; other coatings by "60 °C, 2 h"
  3. The primary aromatic amines item applies only to coatings containing aromatic isocyanates or azo colorants that may generate them — and migration is measured on the finished article, after the coating has fully cured

Footnote 2 is where practice most often goes wrong: cookware and other coatings use different test conditions. A report run under the wrong conditions is worthless even if the numbers look good.

Beyond the four: specific migration limits

Clause 4.3.2 additionally requires base materials to meet the specific migration limits (SML), total specific migration limits (SML(T)) and maximum residue limits (QM) in Annex A and the announcements, and additives to meet GB 9685.

So Table 2 gives the general indicators; each raw material also has its own limits. A full assessment passes both layers.

Responsibilities are split

This edition spells out who does what:

Coating manufacturers (3.2): control risk through formulation design, raw material selection, production process control and product information transfer.

Coating users (3.3): control risk through packaging design at seams and edges, effective barrier layers, cure process control and product information transfer — and reduce coating usage and residue as far as possible while achieving the intended effect.

That last point matters for pan and can makers: if curing is poorly controlled and the coating is under-crosslinked, migration can exceed limits — and the problem is not necessarily the coating supplier.

Export equivalents

  • EU: Regulation (EU) No 10/2011 for plastics, national rules for coatings, and the framework Regulation (EC) No 1935/2004
  • US: FDA 21 CFR Parts 175 and 177 for coatings, plus the Food Contact Notification route
  • Japan: Food Sanitation Act notifications

The logic is similar but the requirements are not interchangeable — do not submit a Chinese report as an EU one.

Four practical tips

  1. Confirm it is a food-contact coating — indirect contact with potential migration counts.
  2. Pick test conditions by product type — cookware differs from other coatings; getting this wrong wastes the report.
  3. Base materials via Annex A, additives via GB 9685 — check both tracks.
  4. Keep evidence of your cure process — exceedances are often incomplete curing rather than bad raw material.

The full GB 4806.10-2025 text (Table 2 general limits, Annex A base material list, migration test conditions) is in the StdFlow knowledge base. Sign up and ask an AI agent for the original text — every answer cited.

FAQ

When did GB 4806.10-2025 take effect?

Published 2 September 2025 and effective 2 September 2026, replacing GB 4806.10-2016 and consolidating base materials for coatings previously spread across 23 official announcements.

Does it apply to non-stick cookware coatings?

Yes. Any coating intended to be applied to food contact materials and articles, in direct or indirect contact with food, is in scope. Note that cookware coatings use different migration test conditions from other coatings.

What is the overall migration limit?

10 mg/dm² or less. For coatings on food contact materials intended for infants and young children, results are converted to mg/kg using the actual area-to-volume ratio, with a limit of 60 mg/kg or less.

Need the full standard text?

Sign up at StdFlow and query the full text and clauses with an AI agent. Every answer carries clause-level citations, with reference-chain tracing. Get $1 free credit on signup.

Sign up free →

More posts